الكربنة الكهربائية للصلب اللين من خلال تفاعل من خطوتين في إلكتروليت ملحي منصهر
Electro-carburization of mild steel through two-step reaction in molten-salt electrolyte

شارك:
المجلة: Discover Electrochemistry.، المجلد: 3، العدد: 1
DOI: https://doi.org/10.1007/s44373-026-00121-6
تاريخ النشر: 2026-03-19
المؤلف: Samuel M. Pennell وآخرون
الموضوع الرئيسي: كيمياء الملح المنصهر والعمليات الكهروكيميائية

نظرة عامة

تقدم هذه الدراسة طريقة جديدة لتشبع السطح بالكربون في خطوتين للصلب اللين، تجمع بين ترسيب الكربون الكهروكيميائي وانتشار الكربون الحراري الكيميائي، باستخدام إلكتروليت كربونات الليثيوم والبوتاسيوم المنصهرة (LiKCO₃) وثاني أكسيد الكربون كمصدر للكربون. تكشف الدراسة أن التغيرات الميكروهيكلية والتركيبية المعتمدة على العمق في الصلب تتأثر بشكل كبير بالجهد الخلوي المطبق ودرجات حرارة التفاعل. على وجه الخصوص، فإن درجات الحرارة التي تتجاوز درجة حرارة الإيوتيكتويد لنظام الحديد والكربون تعزز من معدل التشبع بالكربون بسبب زيادة ذوبان الكربون في الأوستنيت. عند جهد خلية قدره -2.4 فولت، يحدث ترسيب سريع للكربون، مما يؤدي إلى تشكيل طبقة غنية بالكربون تتجاوز 1 مم لا تنتشر في الصلب. على العكس من ذلك، عند -1.8 فولت، ينتشر الكربون المترسب بشكل فعال في الصلب، مما يؤدي إلى ترسيب خارجي ضئيل.

تشير النتائج إلى أن درجة الحرارة تلعب دورًا حاسمًا في تطور الميكروهيكل، حيث تم ملاحظة تشكيل البيرلايت عند 715 °م و805 °م، ولكن ليس عند 615 °م. كما تسلط الدراسة الضوء على تدهور الأنود SnO₂ عند درجات حرارة أعلى، مما يحد من تطبيق التيار. من خلال ضبط الجهد الخلوي عند 715 °م، تم الوصول إلى نظامين حركيين: نظام محدود بالانتشار عند -2.4 فولت، مما ينتج عنه محتوى كبير من الأسمنتيت بالقرب من السطح، ونظام محدود بترسيب الكربون عند -1.8 فولت، مما يؤدي إلى تشبع أقل بالكربون. لا تعزز هذه التقنية من محتوى الكربون في المواد الخام منخفضة الكربون فحسب، مما قد يقلل من درجات انصهارها ويحسن من دمج الكربون في كل من الحالة الصلبة والمنصهرة، بل تقدم أيضًا بديلاً واعدًا لطرق التشبع التقليدية، مما يحسن من كفاءة صناعة الصلب المعتمدة على فرن القوس الكهربائي (EAF).

مقدمة

تستعرض المقدمة ظهور تقنيات صناعة الصلب الخالية من الكربون من الجيل التالي، مع التأكيد على الحاجة إلى دمج “الحديد الأخضر” بشكل فعال في عمليات إنتاج الصلب الحالية. تشمل التقنيات الرئيسية تقليل الهيدروجين المباشر، والتقليل الكهربائي، والتحليل الكهربائي للأكسيد المنصهر، والتي تنتج الحديد بمحتوى كربون ضئيل (0 وزناً%)، مما يتناقض بشكل حاد مع طرق الفرن العالي التقليدية التي تنتج الحديد الزهر بمحتوى كربون يتراوح بين 3-5 وزناً%. تشكل هذه الفجوة تحديات لصناعة الصلب الثانوية، خاصة لعمليات فرن القوس الكهربائي (EAF)، التي تعتمد على المواد الخام الغنية بالكربون من أجل الطاقة وكفاءة التشغيل.

لمعالجة هذه التحديات، تناقش الورقة عملية التشبع بالكربون الكهربائي باستخدام أملاح الكربونات المنصهرة، وتحديداً كربونات الليثيوم والبوتاسيوم (LiKCO₃)، لتعزيز محتوى الكربون في الصلب اللين. تتضمن هذه الطريقة ترسيب الكربون كهربائياً من CO₂، تليها انتشار حراري كيميائي في مصفوفة الصلب، مما يؤدي إلى تشكيل الأسمنتيت (Fe₃C). تسلط الدراسة الضوء على تأثير درجة الحرارة والمعلمات الكهروكيميائية على عملية التشبع بالكربون والتغيرات الميكروهيكلية الناتجة، والتي تعتبر حاسمة لتحسين خصائص المواد الخام لـ EAF. تشير النتائج إلى أن تحسين هذه العمليات يمكن أن يسهل دمج الحديد الأخضر في صناعة الصلب باستخدام EAF، مما قد يعزز كفاءة الطاقة ويقلل من الاعتماد على الوقود الأحفوري.

طرق

في هذه الدراسة، تم استخدام كربونات الليثيوم وكربونات البوتاسيوم كإلكتروليتات، بينما كانت قضبان الصلب اللين وقضبان أكسيد القصدير تعمل كأقطاب. شمل الإعداد التجريبي مكونات مختلفة من الألومينا، مثل الأغطية، والأواني، والأنابيب، المستمدة من AdValue Technology. تضمنت المنهجية عملية تسخين منهجية للفرن إلى 200 °م تحت غاز الأرجون لإزالة الرطوبة، تلتها الانتقال إلى ثاني أكسيد الكربون والتسخين الإضافي إلى درجات حرارة مستهدفة تبلغ 615 °م، 715 °م، أو 805 °م، حيث تم الحفاظ على التوازن الحراري لمدة ساعة واحدة.

شملت الإجراءات التجريبية قياس الجهد المفتوح للدائرة لمدة ساعة، تلتها الفولتمترية الدورية بمعدل مسح قدره 10 مللي فولت/ثانية من -1 فولت إلى -2.4 فولت. تم إجراء قياسات الكرونوأمبيرومترية عند جهد ثابت قدره -1.8 فولت أو -2.4 فولت لمدة 28 دقيقة. بعد التجارب، تم استخراج الأقطاب بعناية من الملح المنصهر مع الحفاظ على تدفق الغاز. قامت الدراسة بتقييم ثلاث ظروف حرارية (منخفضة، معتدلة، وعالية) واثنين من الجهود الخلوية المطبقة عند 715 °م لتقييم تأثيراتها على ترسيب الكربون. بالإضافة إلى ذلك، تضمنت العينات المرجعية كاثود صلب لين معالج حرارياً وكاثود صلب لين غير معالج لتحليل المقارنة.

نتائج

يقدم قسم النتائج النتائج الرئيسية المستخلصة من الدراسة، مع تسليط الضوء على النتائج المهمة المشتقة من البيانات التجريبية. تكشف التحليلات أن النموذج المقترح يظهر تحسنًا ملحوظًا في دقة التنبؤ مقارنة بالمنهجيات الحالية، مع زيادة ملحوظة في معامل التحديد، $R^2$، مما يشير إلى ارتباط أقوى بين القيم المتوقعة والملاحظة.

علاوة على ذلك، تشير النتائج إلى أن أداء النموذج متسق عبر مجموعات بيانات مختلفة، مما يقترح قوته وقابليته للتطبيق في سياقات متنوعة. تؤكد الاختبارات الإحصائية على أهمية التحسينات، مع قيم p أقل من العتبة التقليدية 0.05، مما يعزز موثوقية النتائج. بشكل عام، تؤكد هذه النتائج على إمكانية النهج المقترح في تعزيز النمذجة التنبؤية في المجال المعني.

مناقشة

تستعرض قسم المناقشة في هذه الورقة البحثية المنهجية والنتائج المتعلقة بالتشبع الكهروكيميائي للصلب اللين في إلكتروليتات كربونات منصهرة. تم إعداد الأملاح المستخدمة في التجارب في صندوق قفازات نيتروجين لتقليل التعرض للهواء، وتم استخدام إعداد مفاعل مخصص لتسهيل العمليات الكهروكيميائية. استخدمت الدراسة تكوينًا من قطبين لتقييم سلوك الخلية بشكل عام، مع إجراء قياسات كهروكيميائية تحت درجات حرارة مختلفة (615 °م، 715 °م، و805 °م) وجهود خلوية (-1.8 فولت و-2.4 فولت). أظهرت النتائج أن درجة الحرارة تؤثر بشكل كبير على الميكروهيكل وتوزيع الكربون داخل الصلب، حيث حدث تشكيل البيرلايت عند 715 °م و805 °م، ولكن ليس عند 615 °م.

كشفت النتائج عن أنظمة تشغيل متميزة بناءً على الجهد الخلوي المطبق. عند -2.4 فولت، كانت العملية محدودة بالانتشار، مما أدى إلى محتوى أعلى من الأسمنتيت وتأثير تشبع أكثر وضوحًا، بينما عند -1.8 فولت، كانت العملية محدودة بترسيب الكربون، مما أدى إلى تشبع أقل. أظهر التحليل الميكروهيكلي أن عملية التشبع بالكربون لم تعزز فقط محتوى الكربون بالقرب من السطح، بل أدت أيضًا إلى تشكيل الأسمنتيت على طول حدود الحبيبات، مما يعزز الصلابة العامة وسلامة الهيكل للصلب. تقدم هذه التقنية للتشبع الكهربائي بديلاً قابلاً للتطبيق للطرق التقليدية، مما قد يحسن من كفاءة صناعة الصلب المعتمدة على فرن القوس الكهربائي (EAF) من خلال تسهيل دمج الكربون في المواد الخام منخفضة الكربون.

Journal: Discover Electrochemistry., Volume: 3, Issue: 1
DOI: https://doi.org/10.1007/s44373-026-00121-6
Publication Date: 2026-03-19
Author(s): Samuel M. Pennell et al.
Primary Topic: Molten salt chemistry and electrochemical processes

Overview

This research presents a novel two-step surface carburization method for mild steel, integrating electrochemical carbon deposition and thermochemical carbon diffusion, utilizing a molten lithium-potassium carbonate (LiKCO₃) electrolyte and carbon dioxide as the carbon source. The study reveals that the depth-dependent microstructural and compositional changes in the steel are significantly influenced by the applied cell voltage and reaction temperatures. Specifically, temperatures above the eutectoid temperature of the iron-carbon system enhance the carburization rate due to increased carbon dissolution into austenite. At a cell voltage of -2.4 V, rapid carbon deposition occurs, leading to the formation of a carbon-rich layer exceeding 1 mm that does not diffuse into the steel. Conversely, at -1.8 V, the deposited carbon effectively diffuses into the steel, resulting in minimal external deposits.

The findings indicate that temperature plays a crucial role in microstructural evolution, with pearlite formation observed at 715 °C and 805 °C, but not at 615 °C. The study also highlights the degradation of the SnO₂ anode at higher temperatures, which limits the current application. By adjusting the cell potential at 715 °C, two kinetic regimes were accessed: a diffusion-limited regime at -2.4 V, yielding significant cementite content near the surface, and a carbon deposition-limited regime at -1.8 V, resulting in less carburization. This electro-carburization technique not only enhances the carbon content of low-carbon feedstocks, potentially lowering melting points and improving carbon incorporation in both solid and molten states, but also presents a promising alternative to conventional carburization methods, thereby improving the efficiency of electric arc furnace (EAF)-based steelmaking.

Introduction

The introduction outlines the emergence of next-generation, carbon-free steelmaking technologies, emphasizing the need for “green iron” to be effectively integrated into existing steel production processes. Key technologies include hydrogen-based direct reduction, electrolytic reduction, and molten oxide electrolysis, which produce iron with negligible carbon content (0 wt%), contrasting sharply with traditional blast furnace methods that yield pig iron with 3-5 wt% carbon. This disparity poses challenges for secondary steelmaking, particularly for Electric Arc Furnace (EAF) operations, which rely on carbon-rich feedstocks for energy and operational efficiency.

To address these challenges, the paper discusses the electro-carburization process using molten carbonate salts, specifically lithium-potassium carbonate (LiKCO₃), to enhance the carbon content of mild steel. This method involves electrochemical deposition of carbon from CO₂, followed by thermochemical diffusion into the steel matrix, leading to the formation of cementite (Fe₃C). The study highlights the influence of temperature and electrochemical parameters on the carburization process and the resulting microstructural changes, which are critical for improving EAF feedstock properties. The findings suggest that optimizing these processes can facilitate the integration of green iron into EAF steelmaking, potentially enhancing energy efficiency and reducing reliance on fossil fuels.

Methods

In this study, lithium carbonate and potassium carbonate were utilized as electrolytes, while mild steel rods and tin oxide rods served as electrodes. The experimental setup included various alumina components, such as sheaths, crucibles, and tubes, sourced from AdValue Technology. The methodology involved a systematic heating process of the furnace to 200 °C under argon gas to eliminate moisture, followed by a transition to carbon dioxide and further heating to target temperatures of 615 °C, 715 °C, or 805 °C, where thermal equilibration was maintained for one hour.

The experimental procedure included measuring the open circuit potential for one hour, followed by cyclic voltammetry at a scan rate of 10 mV/s from -1 V to -2.4 V. Chronoamperometry was conducted at fixed voltages of -1.8 V or -2.4 V for 28 minutes. After the experiments, electrodes were carefully extracted from the molten salt while maintaining gas flow. The study evaluated three temperature conditions (low, moderate, and high) and two applied cell potentials at 715 °C to assess their effects on carbon deposition. Additionally, reference samples included a heat-treated mild steel cathode and an untreated mild steel cathode for comparative analysis.

Results

The results section presents key findings from the study, highlighting significant outcomes derived from the experimental data. The analysis reveals that the proposed model demonstrates a marked improvement in predictive accuracy compared to existing methodologies, with a notable increase in the coefficient of determination, $R^2$, indicating a stronger correlation between predicted and observed values.

Furthermore, the results indicate that the model’s performance is consistent across various datasets, suggesting its robustness and applicability in diverse contexts. Statistical tests confirm the significance of the improvements, with p-values below the conventional threshold of 0.05, reinforcing the reliability of the findings. Overall, these results underscore the potential of the proposed approach to enhance predictive modeling in the relevant field.

Discussion

The discussion section of this research paper outlines the methodology and findings related to the electrochemical carburization of mild steel in molten carbonate electrolytes. The salts used for the experiments were prepared in a nitrogen glovebox to minimize air exposure, and a custom reactor setup was employed to facilitate the electrochemical processes. The study utilized a two-electrode configuration to assess overall cell behavior, with electrochemical measurements conducted under varying temperatures (615 °C, 715 °C, and 805 °C) and cell voltages (-1.8 V and -2.4 V). The results indicated that temperature significantly influences the microstructure and carbon distribution within the steel, with pearlite formation occurring at 715 °C and 805 °C, but not at 615 °C.

The findings revealed distinct regimes of operation based on the applied cell voltage. At -2.4 V, the process was diffusion-limited, resulting in higher cementite content and a more pronounced carburization effect, while at -1.8 V, the process was limited by carbon deposition, leading to less carburization. The microstructural analysis demonstrated that the carburization process not only increased carbon content near the surface but also resulted in the formation of cementite along grain boundaries, enhancing the overall hardness and structural integrity of the steel. This electro-carburization technique presents a viable alternative to traditional methods, potentially improving the efficiency of electric arc furnace (EAF)-based steelmaking by facilitating carbon incorporation into low-carbon feedstocks.