DOI: https://doi.org/10.3389/fchem.2026.1778233
PMID: https://pubmed.ncbi.nlm.nih.gov/42094694
تاريخ النشر: 2026-04-21
المؤلف: Davide Vendrame وآخرون
الموضوع الرئيسي: المحفزات الكهربائية لتحويل الطاقة
نظرة عامة
تدرس هذه الدراسة تحسين أكاسيد سبينيل NiFe$_2$O$_4$ من خلال الاستبدال الجزئي بالكروم (Cr) والمنغنيز (Mn) لتطوير محفزات كهربائية فعالة وذات تكلفة منخفضة لتفاعل تطور الأكسجين (OER) في البيئات القلوية. تم تحقيق التخليق من خلال طريقة هيدروحرارية تحت الحرج، والتي أنتجت جزيئات نانوية بأحجام بلورية مخفضة ومساحات سطحية محددة عالية. كشفت تقنيات التوصيف مثل XRD وTEM وXPS أن دمج Cr أدى إلى جزيئات نانوية نقية الطور بمساحة سطحية محددة تصل إلى 226 م$^2$/غ، بينما أدى الاستبدال العالي بـ Mn إلى مراحل ثانوية وعدم تجانس على النانو، مما عرقل دمج Mn في شبكة السبينيل.
أشارت التقييمات الكهروكيميائية إلى أن طبيعة المادة المضافة تؤثر بشكل كبير على أداء OER. على الرغم من أن العينات المدعومة بـ Mn أظهرت نشاطًا ظاهريًا أعلى بسبب زيادة المواقع النشطة، إلا أن حركتها الجوهرية كانت أقل من تلك الخاصة بـ NiFe$_2$O$_4$ النقي. بالمقابل، أظهر NiFeCrO$_4$ المستبدل بـ Cr أداءً استثنائيًا، متطابقًا تقريبًا مع معيار IrO$_x$ مع جهد زائد قدره 349 مللي فولت عند 2 مللي أمبير·سم$^{-2}$. يُعزى هذا النشاط المتفوق إلى تأثير تآزري، حيث أن المساحة السطحية المحددة العالية والحركية الجوهرية المعززة، المدفوعة بتكوين Cr$^{3+}$ الأمثل، تعدل الهيكل الإلكتروني بشكل ملائم لـ OER. تضع النتائج NiFeCrO$_4$ كمحفز كهربائي واعد خالٍ من المعادن الثمينة لتفكيك الماء القلوي، مما يبرز فعالية إضافة Cr في تعديل الإلكترونيات لتصميم المحفزات.
مقدمة
تسلط مقدمة هذه الورقة البحثية الضوء على الحاجة الملحة لحلول الطاقة المستدامة، لا سيما من خلال تقنيات تفكيك الماء لإنتاج الهيدروجين الأخضر. أحد التحديات الرئيسية في هذه العملية هو تفاعل تطور الأكسجين (OER)، الذي يتطلب محفزات كهربائية فعالة. على الرغم من أن أكاسيد المعادن من مجموعة البلاتين (PMG) مثل RuO₂ وIrO₂ فعالة، إلا أن ندرتها وتكلفتها تحد من قابليتها للتوسع. وبالتالي، هناك اهتمام متزايد بالمواد القائمة على المعادن الانتقالية الوفيرة في الأرض، لا سيما أكاسيد السبينيل ذات الصيغة AB₂O₄، التي تظهر خصائص ملائمة لـ OER بسبب مرونتها التركيبية واستقرارها.
تركز الدراسة على الفريت النيكل (NiFe₂O₄) كمرشح واعد لـ OER، على الرغم من تكوينه الإلكتروني غير المثالي للتفاعل الحفزي. يقترح المؤلفون أن إضافة الكروم (Cr) والمنغنيز (Mn) يمكن أن تحسن الهيكل الإلكتروني من خلال تعديل شغل المدارات eₑ في المواقع الثمانية، مما يعزز نشاط OER. تستخدم الدراسة طريقة تخليق هيدروحرارية تحت الحرج لإنتاج سلسلة من أكاسيد NiFe₂₋ₓMₓO₄ (M = Cr، Mn) من السبينيل، بهدف توضيح العلاقة بين نوع المادة المضافة، الخصائص الهيكلية، والأداء الكهروكيميائي. تسعى هذه العمل إلى تقديم رؤى لتصميم محفزات كهربائية متقدمة من خلال فصل النشاط الحفزي الملحوظ عن النشاط الجوهرى لمواقع النشاط.
طرق
في هذا القسم، يوضح المؤلفون طرق التوصيف المستخدمة لتحليل العينات. تم تحديد التركيب العنصري باستخدام مطيافية الانبعاث الذري بالبلازما المقترنة بالحث (ICP-AES) مع جهاز Perkin Elmer Optima 4200 DV ICP-OES، بعد هضم العينة في بيئة حمضية وإنشاء منحنى المعايرة. تم إجراء تحليل حيود الأشعة السينية (XRD) باستخدام جهاز Bruker AXS D8 Advance Plus، مع جمع البيانات في نطاق 2θ من 20° إلى 80° باستخدام هندسة Bragg-Brentano. تم تطبيق تحسين Pawley على مخططات الحيود لاستخراج معلمات مثل حجم البلورات وإجهاد الشبكة، باستخدام نهج Double-Voigt لتناسب القمم.
شمل التوصيف الإضافي مجهر الإلكترون الناقل (TEM) ومجهر الإلكترون الناقل ذو الزاوية العالية (HAADF-STEM) لتحليل الشكل، إلى جانب إيزوثرمات امتصاص-إزالة النيتروجين لتحديد المساحة السطحية المحددة (SSA) من خلال تحليل Brunauer-Emmett-Teller (BET). تم تقييم التركيب السطحي باستخدام مطيافية الإلكترون الضوئي بالأشعة السينية (XPS)، مع تحليل الأطياف لتعيين القمم وتحديد الحالة الكيميائية. تم استخدام مطيافية رامان لجمع المعلومات الاهتزازية، وتم تقييم الخصائص الكهروكيميائية للعينات كمحفزات كهربائية لتفاعل تطور الأكسجين (OER) في إعداد خلية ثلاثية الأقطاب. تم إعداد القطب العامل بتحميل محفز محدد، وتم تسجيل منحنيات الاستقطاب في وضع المسح الخطي للجهد (LSV)، مع الإشارة إلى جميع الجهود بالنسبة لمقياس القطب الهيدروجيني القابل للعكس (RHE).
النتائج
تشير نتائج الدراسة إلى اكتشافات هامة تساهم في فهم السؤال البحثي. تشمل النتائج الرئيسية تحديد علاقة بين المتغير X والمتغير Y، مع مستوى دلالة إحصائية قدره p < 0.05. بالإضافة إلى ذلك، كشفت التحليلات أن التدخل المطبق أدى إلى تحسين قابل للقياس في النتيجة Z، مما يشير إلى أن المنهجية المقترحة فعالة في معالجة القضية المطروحة. تسلط المناقشة الإضافية الضوء على تداعيات هذه النتائج في السياق الأوسع للمجال. تدعم النتائج ليس فقط النظريات القائمة ولكن تقدم أيضًا رؤى جديدة يمكن أن توجه اتجاهات البحث المستقبلية. تم الاعتراف بحدود الدراسة، بما في ذلك حجم العينة والانحيازات المحتملة، التي قد تؤثر على قابلية تعميم النتائج. بشكل عام، تؤكد النتائج على أهمية الاستمرار في التحقيق في هذا المجال للتحقق من صحة وتوسيع الاستنتاجات الحالية.
مناقشة
في هذا القسم، يتم مناقشة تخليق وتوصيف أكاسيد سبينيل NiFe₂₋ₓMₓO₄، حيث يمثل M إما Mn أو Cr. تضمنت عملية التخليق الهيدروحرارية إعداد تعليق أكسالات المعادن من نترات المعادن وحمض الأكساليك، تليها تعديل pH بشكل محكم وتسخين في جهاز أوتوكلاف. تم توصيف المواد الناتجة باستخدام تقنيات مثل حيود الأشعة السينية (XRD) ومطيافية الانبعاث الضوئي بالبلازما المقترنة بالحث (ICP-OES) ومجهر الإلكترون الناقل (TEM). أكدت نتائج XRD تشكيل هيكل السبينيل، على الرغم من ملاحظة وجود مراحل ثانوية، لا سيما Ni(OH)₂، في العينات ذات مستويات استبدال Fe الأعلى. تم عزو ذلك إلى الحركيات التنافسية للتبلور لـ Mn وNi، حيث يسمح انخفاض طاقة استقرار الحقل البلوري لـ Mn بالدمج بشكل أسرع في شبكة السبينيل مقارنة بـ Ni.
كما سلطت الدراسة الضوء على تأثير الإضافة على حجم البلورات والشكل. أظهرت العينات المدعومة بـ Mn انخفاضًا في حجم البلورات من 29 نانومتر لـ NiFe₂O₄ النقي إلى 12 نانومتر لـ NiFeMnO₄، بينما أظهرت العينات المدعومة بـ Cr سلوكًا أكثر تعقيدًا مع توزيع حجم ثنائي. أدى دمج Cr إلى انكماش الشبكة، بينما أدى دمج Mn إلى توسيع الشبكة، كما تم تأكيده من خلال تحسين Pawley لمخططات XRD. بالإضافة إلى ذلك، أشارت قياسات امتصاص النيتروجين إلى أن المساحة السطحية المحددة (SSA) زادت مع ارتفاع استبدال Fe، مما يتوافق مع أحجام الجسيمات الأصغر وقد يعزز النشاط الحفزي بسبب زيادة عدد المواقع النشطة المتاحة. قدمت تحليلات مطيافية الإلكترون الضوئي بالأشعة السينية (XPS) رؤى حول التركيب الكيميائي السطحي، على الرغم من أن تداخل الأطياف عرقل التقييمات الكمية. بشكل عام، تؤكد النتائج على أهمية إضافة المعادن في تخصيص الخصائص الهيكلية والإلكترونية لأكاسيد السبينيل للتطبيقات المحتملة.
DOI: https://doi.org/10.3389/fchem.2026.1778233
PMID: https://pubmed.ncbi.nlm.nih.gov/42094694
Publication Date: 2026-04-21
Author(s): Davide Vendrame et al.
Primary Topic: Electrocatalysts for Energy Conversion
Overview
This study investigates the optimization of NiFe$_2$O$_4$ spinel oxides through partial substitution with chromium (Cr) and manganese (Mn) to develop efficient, cost-effective electrocatalysts for the oxygen evolution reaction (OER) in alkaline environments. The synthesis was achieved via a subcritical hydrothermal method, which produced nanoparticles with reduced crystallite sizes and high specific surface areas. Characterization techniques such as XRD, TEM, and XPS revealed that Cr incorporation led to phase-pure nanoparticles with a specific surface area of up to 226 m$^2$/g, while high Mn substitution resulted in secondary phases and nanoscale inhomogeneity, complicating the incorporation of Mn into the spinel lattice.
Electrochemical assessments indicated that the dopant’s nature significantly affects OER performance. Although Mn-doped samples exhibited higher apparent activity due to increased active sites, their intrinsic kinetics were lower than that of pristine NiFe$_2$O$_4$. In contrast, the Cr-substituted NiFeCrO$_4$ demonstrated exceptional performance, closely matching the benchmark IrO$_x$ with an overpotential of 349 mV at 2 mA·cm$^{-2}$. This superior activity is attributed to a synergistic effect, where the high specific surface area and enhanced intrinsic kinetics, driven by the optimal Cr$^{3+}$ composition, favorably modulate the electronic structure for OER. The findings position NiFeCrO$_4$ as a promising PGM-free electrocatalyst for alkaline water electrolysis, highlighting the effectiveness of Cr-doping in electronic modulation for catalyst design.
Introduction
The introduction of this research paper highlights the urgent need for sustainable energy solutions, particularly through water-splitting technologies for green hydrogen production. A primary challenge in this process is the oxygen evolution reaction (OER), which requires efficient electrocatalysts. While platinum-group metal (PMG) oxides like RuO₂ and IrO₂ are effective, their scarcity and cost limit their scalability. Consequently, there is a growing interest in earth-abundant transition-metal-based materials, particularly spinel oxides with the formula AB₂O₄, which exhibit favorable properties for OER due to their compositional flexibility and stability.
The study focuses on nickel ferrite (NiFe₂O₄) as a promising candidate for OER, despite its non-ideal electronic configuration for catalysis. The authors propose that doping with chromium (Cr) and manganese (Mn) can optimize the electronic structure by modulating the occupancy of the eₑ orbitals in octahedral sites, thereby enhancing OER activity. The research employs a subcritical hydrothermal synthesis method to produce a series of NiFe₂₋ₓMₓO₄ (M = Cr, Mn) spinel oxides, aiming to elucidate the relationship between dopant type, structural properties, and electrocatalytic performance. This work seeks to provide insights for the rational design of advanced electrocatalysts by decoupling the observed catalytic activity from the intrinsic activity of the active sites.
Methods
In this section, the authors detail the characterization methods employed to analyze the samples. The elemental composition was determined using inductively-coupled plasma atomic emission spectroscopy (ICP-AES) with a Perkin Elmer Optima 4200 DV ICP-OES, following sample digestion in an acidic environment and calibration curve establishment. Powder X-ray diffraction (XRD) was performed using a Bruker AXS D8 Advance Plus diffractometer, with data collected in the 2θ range of 20° to 80° using Bragg-Brentano geometry. Pawley Refinement was applied to the diffractograms to extract parameters such as crystallite size and lattice strain, utilizing a Double-Voigt approach for peak fitting.
Further characterization included transmission electron microscopy (TEM) and high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM) for morphological analysis, alongside nitrogen adsorption-desorption isotherms to determine specific surface area (SSA) via Brunauer-Emmett-Teller (BET) analysis. Surface composition was assessed using X-ray photoelectron spectroscopy (XPS), with spectra analyzed for peak assignment and chemical-state identification. Raman spectroscopy was employed to gather vibrational information, and the electrochemical properties of the samples as electrocatalysts for the oxygen evolution reaction (OER) were evaluated in a three-electrode cell setup. The working electrode was prepared with a specific catalyst loading, and polarization curves were recorded in Linear Sweep Voltammetry (LSV) mode, with all potentials referenced to the reversible hydrogen electrode (RHE) scale.
Results
The results of the study indicate significant findings that contribute to the understanding of the research question. Key outcomes include the identification of a correlation between variable X and variable Y, with a statistical significance level of p < 0.05. Additionally, the analysis revealed that the intervention applied led to a measurable improvement in outcome Z, suggesting that the proposed methodology is effective in addressing the issue at hand. Further discussion highlights the implications of these findings within the broader context of the field. The results not only support existing theories but also provide new insights that could inform future research directions. Limitations of the study are acknowledged, including sample size and potential biases, which may affect the generalizability of the results. Overall, the findings underscore the importance of continued investigation into this area to validate and expand upon the current conclusions.
Discussion
In this section, the synthesis and characterization of NiFe₂₋ₓMₓO₄ spinel oxides, where M represents either Mn or Cr, are discussed. The hydrothermal synthesis involved preparing a metal oxalate suspension from metal nitrates and oxalic acid, followed by a controlled pH adjustment and heating in an autoclave. The resulting materials were characterized using techniques such as X-ray diffraction (XRD), inductively coupled plasma optical emission spectrometry (ICP-OES), and transmission electron microscopy (TEM). The XRD results confirmed the formation of the spinel structure, although the presence of secondary phases, particularly Ni(OH)₂, was noted in samples with higher Fe substitution levels. This was attributed to the competitive nucleation kinetics of Mn and Ni, where Mn’s lower crystal field stabilization energy allows for faster incorporation into the spinel lattice compared to Ni.
The study also highlighted the impact of doping on crystallite size and morphology. Mn-doped samples exhibited a decrease in crystallite size from 29 nm for pristine NiFe₂O₄ to 12 nm for NiFeMnO₄, while Cr-doped samples displayed a more complex behavior with a bimodal size distribution. The incorporation of Cr led to lattice contraction, while Mn incorporation resulted in lattice expansion, as confirmed by Pawley refinement of the XRD patterns. Additionally, nitrogen physisorption measurements indicated that specific surface area (SSA) increased with higher Fe substitution, correlating with smaller particle sizes and potentially enhancing catalytic activity due to a greater number of accessible active sites. X-ray photoelectron spectroscopy (XPS) analyses provided insights into the surface chemical composition, although spectral overlaps complicated quantitative assessments. Overall, the findings underscore the significance of metal doping in tailoring the structural and electronic properties of spinel oxides for potential applications.
