دراسة آلية حول تشقق التآكل الناتج عن الإجهاد للسبائك AA5083 الحساسة في منطقة محاكاة تقلب مستوى المياه: تحليل مدمج للمقاومة واختبارات الشد
A mechanistic study on stress corrosion cracking of sensitized AA5083 in a simulated water level fluctuation zone: Combined impedance analysis and tensile tests

شارك:
المجلة: Corrosion Science، المجلد: 245
DOI: https://doi.org/10.1016/j.corsci.2025.112701
تاريخ النشر: 2025-01-13
المؤلف: Zhe Liu وآخرون
الموضوع الرئيسي: سلوك التآكل والتثبيط

نظرة عامة

تقدم هذه القسم نظرة عامة على مقال بحثي تم تحسينه بعد القبول ولكنه ليس النسخة النهائية المنشورة بعد. ويبرز أن الوثيقة قد تحتوي على أخطاء بسبب العمليات الإنتاجية المستمرة، وتطبق الإخلاءات القانونية ذات الصلة بالمجلة.

في الاستنتاجات المتعلقة بتصدع التآكل الناتج عن الضغط (SCC) لسبائك AA5083-O الحساسة في بيئة تتقلب فيها مستويات المياه، يتم تقديم ثلاث نتائج رئيسية: (1) تشير تحليل المقاومة إلى تشكيل فيلم أكسيد مزدوج الطبقة على السبيكة الحساسة، مع طبقة داخلية متجانسة وطبقة خارجية ذات تدرج كيميائي. ومن الجدير بالذكر أن سمك الطبقة الداخلية يتناقص وتضعف خصائصها الواقية تحت ظروف الغمر المتكرر مقارنة بالغمر الكامل. (2) تزداد القابلية لـ SCC مع زيادة وقت التعرض، حيث تصل إلى ذروتها بحوالي 78% بعد 120 دقيقة، مع تحديد نقطة زمنية حرجة بين 30-60 دقيقة، تتوافق مع تبخر طبقة الإلكتروليت على السطح. (3) يؤثر التفاعل بين فترات الغمر والتعرض بشكل كبير على SCC، مما يشير إلى أن أوقات التعرض الممتدة في الظروف المتكررة تؤثر على قابلية المادة للتآكل.

مقدمة

تناقش مقدمة الورقة أهمية سبائك الألمنيوم-المغنيسيوم (سلسلة 5xxx) في التطبيقات البحرية، مع تسليط الضوء على خصائصها المرغوبة مثل القوة النوعية العالية، وقابلية اللحام الجيدة، ومقاومة التآكل الممتازة. ومع ذلك، تواجه هذه السبائك تحديات تتعلق بتصدع التآكل الناتج عن الضغط (SCC) بسبب ترسيب طور Al3Mg2 الأنودي (الطور β) عند تعرضها لدرجات حرارة مرتفعة ومستويات مغنيسيوم مشبعة. تختلف القابلية لـ SCC بشكل كبير عبر بيئات بحرية مختلفة، لا سيما في منطقة تقلب مستوى المياه، التي تشمل مناطق فرعية ذات أوقات غمر-تعرض متناوبة مختلفة.

يشير المؤلفون إلى أن الأبحاث السابقة ركزت بشكل أساسي على مرحلة الغمر من التآكل، متجاهلة تأثيرات طبقة الإلكتروليت الرقيقة (TEL) خلال مرحلة التعرض. ويؤكدون على الحاجة إلى مزيد من التحقيق في آليات SCC لسبائك AA5083 تحت ظروف الغمر-التعرض، خاصة بالنظر إلى تأثير TEL على عمليات التآكل. لمعالجة هذه الفجوة، تقدم الدراسة جهاز محاكاة جديد مصمم لتكرار منطقة تقلب مستوى المياه، مما يسمح بتقييم منهجي لتأثيرات أوقات الغمر والتعرض المتناوبة على SCC لسبائك AA5083-O الحساسة. تستخدم الأبحاث منهجيات متنوعة، بما في ذلك اختبارات الشد بمعدل إجهاد بطيء وتحليل الطيف الكهروكيميائي، لتحليل التأثيرات التآزرية للتآكل والضغط، بهدف تعزيز الفهم وتصميم سبائك الألمنيوم البحرية في البيئات المعقدة.

طرق

في هذه الدراسة، بحث الباحثون سلوك تصدع التآكل الناتج عن الضغط (SCC) لسبائك الألمنيوم AA5083-O، التي تحتوي على تركيبة كيميائية محددة تتكون بشكل أساسي من الألمنيوم (Al) مع المغنيسيوم (Mg) وعناصر سبائكية أخرى. تم تحسس صفائح السبيكة من خلال الشيخوخة عند 150 درجة مئوية لمدة تصل إلى 144 ساعة قبل أن يتم تبريدها في الهواء، مما أسفر عن عينات أظهرت SCC ملحوظ مقارنة بالسبائك المستلمة.

شمل الإعداد التجريبي جهازًا محركًا مصممًا لمحاكاة تقلبات مستوى المياه، والذي تضمن نظام اختبار كهروكيميائي وآلية تحكم زمنية. تم غمر عينة شد من AA5083-O في محلول NaCl بتركيز 3.5 wt. %، مع تقلب مستويات المياه بين حالات الغمر والتعرض التي يتم التحكم فيها بواسطة مشغل كهربائي. تم إجراء مجموعتين من التجارب لتقييم تأثير نسب أوقات الغمر-التعرض المختلفة (EIRs) على SCC. تضمنت المجموعة الأولى غمرًا كاملًا واحدًا وثلاثة ظروف EIR متغيرة، بينما ركزت المجموعة الثانية على EIR1، حيث تم فحص تأثيرات دورات الغمر-التعرض المختلفة مع معلمات زمنية تتراوح من 1-1 إلى 120-120 دقيقة. تم إجراء جميع التجارب في درجة حرارة الغرفة (25±2 درجة مئوية).

نتائج

يقدم قسم “النتائج” من ورقة البحث النتائج الرئيسية المستمدة من التجارب أو التحليلات التي تم إجراؤها. عادة ما يتضمن بيانات كمية، وتحليلات إحصائية، وتمثيلات بصرية مثل الرسوم البيانية أو الجداول لتوضيح النتائج. غالبًا ما تتم مقارنة النتائج مع الفرضيات الأولية أو المعايير، مما يبرز الاتجاهات المهمة، أو العلاقات، أو الشذوذات التي لوحظت خلال الدراسة.

في هذا القسم، قد يناقش المؤلفون أيضًا تداعيات نتائجهم، مؤكدين كيف تساهم في المعرفة الحالية في هذا المجال. من المحتمل أيضًا معالجة أي قيود واجهت خلال البحث، بالإضافة إلى الطرق المحتملة للتحقيق في المستقبل، لتوفير فهم شامل للنتائج وأهميتها.

مناقشة

تتناول قسم المناقشة من ورقة البحث النتائج من اختبارات التآكل المختلفة التي أجريت على سبائك الألمنيوم AA5083-O الحساسة، مع التركيز على القابلية للتآكل بين الحبيبات (IGC) وتصدع التآكل الناتج عن الضغط (SCC). أظهر اختبار فقدان الكتلة بحمض النيتريك (NAMLT) أن العينات الحساسة أظهرت زيادة ملحوظة في درجة التحسس (DoS)، حيث ارتفعت القيم من 1.3 ± 0.2 ملغ/سم² للعينات غير الحساسة إلى 57.2 ± 1.6 ملغ/سم² بعد التحسس، مما يشير إلى قابلية ملحوظة لـ IGC. أظهرت اختبارات الشد بمعدل إجهاد بطيء (SSRT) أنه بينما حافظت السبيكة على استطالة تبلغ حوالي 41% في الهواء، انخفضت هذه النسبة إلى حوالي 11% في محلول NaCl بتركيز 3.5 wt. %، مما يبرز ضعف السبيكة أمام SCC.

كشفت التحليلات المجهرية باستخدام المجهر الإلكتروني الماسح (SEM) وتحليل الطيف بالأشعة السينية المشتتة للطاقة (EDS) أن التحسس أدى إلى تشكيل شبكة مستمرة من الرواسب الغنية بالمغنيسيوم على طول حدود الحبيبات، والتي تعمل كمواقع لبدء الشقوق. أكدت اختبارات تحليل الطيف الكهروكيميائي (EIS) أيضًا أن زيادة الضغط وأوقات الغمر الممتدة في البيئات التآكلية تقلل بشكل كبير من مقاومة SCC للسبيكة. تشير النتائج إلى أن سمك الفيلم الأكسيدي وتجانسه هما عاملان حاسمان يؤثران على سلوك التآكل، حيث ترتبط الأفلام الرقيقة بمعدلات تآكل أعلى. بشكل عام، تؤكد النتائج على الآثار الضارة للتحسس والعوامل البيئية على السلامة الميكانيكية لـ AA5083-O، مما يبرز الحاجة إلى اعتبار دقيق في التطبيقات التي تكون فيها مقاومة التآكل أمرًا بالغ الأهمية.

Journal: Corrosion Science, Volume: 245
DOI: https://doi.org/10.1016/j.corsci.2025.112701
Publication Date: 2025-01-13
Author(s): Zhe Liu et al.
Primary Topic: Corrosion Behavior and Inhibition

Overview

The section provides an overview of a research article that has been enhanced post-acceptance but is not yet the final published version. It highlights that the document may contain errors due to ongoing production processes, and legal disclaimers relevant to the journal apply.

In the conclusions regarding stress corrosion cracking (SCC) of sensitized AA5083-O in a fluctuating water level environment, three key findings are presented: (1) The resistivity analysis indicates the formation of a double-layer oxide film on the sensitized alloy, with a homogeneous inner layer and a chemically gradient outer layer. Notably, the inner layer’s thickness diminishes and its protective qualities weaken under cyclic immersion-exposure conditions compared to full immersion. (2) The susceptibility to SCC increases with prolonged exposure time, peaking at approximately 78% after 120 minutes, with a critical time point identified between 30-60 minutes, correlating with the evaporation of the electrolyte layer on the surface. (3) The interplay between immersion and exposure durations significantly affects SCC, suggesting that extended exposure times in cyclic conditions influence the material’s susceptibility to corrosion.

Introduction

The introduction of the paper discusses the significance of aluminum-magnesium (5xxx series) alloys in marine applications, highlighting their desirable properties such as high specific strength, good weldability, and excellent corrosion resistance. However, these alloys face challenges related to stress corrosion cracking (SCC) due to the precipitation of the anodic Al3Mg2 phase (β phase) when exposed to elevated temperatures and supersaturated magnesium levels. The susceptibility to SCC varies significantly across different marine environments, particularly in the water level fluctuation zone, which includes subzones with differing immersed-exposed alternating times.

The authors note that previous research primarily focused on the immersed phase of corrosion, neglecting the effects of the thin electrolyte layer (TEL) during the exposed phase. They emphasize the need for further investigation into the SCC mechanisms of AA5083 alloys under immersed-exposed conditions, particularly given the influence of the TEL on corrosion processes. To address this gap, the study introduces a novel simulation device designed to replicate the water level fluctuation zone, allowing for a systematic evaluation of the effects of alternating immersion and exposure times on the SCC of sensitized AA5083-O. The research employs various methodologies, including slow strain rate tensile tests and electrochemical impedance spectroscopy, to analyze the synergistic effects of corrosion and stress, ultimately aiming to enhance the understanding and design of marine aluminum alloys in complex environments.

Methods

In this study, the researchers investigated the stress corrosion cracking (SCC) behavior of AA5083-O aluminum alloy, which has a specific chemical composition predominantly consisting of aluminum (Al) with magnesium (Mg) and other alloying elements. The alloy plates were sensitized through aging at 150 °C for up to 144 hours before being air-cooled, resulting in samples that exhibited significant SCC compared to as-received alloys.

The experimental setup involved a motorized device designed to simulate water level fluctuations, which included an electrochemical testing system and a time-control mechanism. A tensile specimen of AA5083-O was submerged in a 3.5 wt.% NaCl solution, with water levels fluctuating between immersed and exposed states controlled by an electric actuator. Two groups of experiments were conducted to assess the impact of different immersed-exposed time ratios (EIRs) on SCC. The first group included one full immersion and three varying EIR conditions, while the second group focused on EIR1, examining the effects of different immersed-exposed cycles with time parameters ranging from 1-1 to 120-120 minutes. All experiments were conducted at ambient temperature (25±2 °C).

Results

The “Results” section of the research paper presents key findings derived from the conducted experiments or analyses. It typically includes quantitative data, statistical analyses, and visual representations such as graphs or tables to illustrate the outcomes. The results are often compared against the initial hypotheses or benchmarks, highlighting significant trends, correlations, or anomalies observed during the study.

In this section, the authors may also discuss the implications of their findings, emphasizing how they contribute to the existing body of knowledge in the field. Any limitations encountered during the research, as well as potential avenues for future investigation, are also likely addressed to provide a comprehensive understanding of the results and their relevance.

Discussion

The discussion section of the research paper details the findings from various corrosion tests conducted on sensitized AA5083-O aluminum alloy, focusing on the susceptibility to intergranular corrosion (IGC) and stress corrosion cracking (SCC). The Nitric Acid Mass Loss Test (NAMLT) revealed that sensitized samples exhibited a significant increase in the degree of sensitization (DoS), with values rising from 1.3 ± 0.2 mg/cm² for unsensitized samples to 57.2 ± 1.6 mg/cm² post-sensitization, indicating a marked susceptibility to IGC. The slow strain rate tensile (SSRT) tests demonstrated that while the alloy maintained an elongation of approximately 41% in air, this dropped to around 11% in a 3.5 wt.% NaCl solution, underscoring the alloy’s vulnerability to SCC.

Microstructural analyses using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS) revealed that sensitization led to the formation of a continuous network of Mg-rich precipitates along grain boundaries, which serve as sites for crack initiation. The electrochemical impedance spectroscopy (EIS) tests further confirmed that increased stress and prolonged immersion times in corrosive environments significantly reduced the SCC resistance of the alloy. The results indicate that the oxide film’s thickness and homogeneity are critical factors influencing corrosion behavior, with thinner films correlating with higher corrosion rates. Overall, the findings emphasize the detrimental effects of sensitization and environmental factors on the mechanical integrity of AA5083-O, highlighting the need for careful consideration in applications where corrosion resistance is paramount.