DOI: https://doi.org/10.62755/gsm.2026.02
تاريخ النشر: 2026-05-05
المؤلف: Rut Rabekka Gultom وآخرون
الموضوع الرئيسي: تقنيات التحفيز الضوئي المتقدمة
نظرة عامة
تتناول هذه الدراسة القضية الملحة لتلوث صبغات الأقمشة من خلال تطوير محفزات ضوئية فعالة لمعالجة مياه الصرف. قام الباحثون بتصنيع أغشية الألياف النانوية من بولي أكريلونيتريل/بولي فينيل بيروليدون/أكسيد الزنك (PAN/PVP/ZnO) من خلال تقنية النانو، مع تغيير تحميلات ZnO عند 0 و0.5 و1 و2 مللي مول. أظهرت المجهر الإلكتروني الماسح (SEM) تكوين ألياف نانوية مستمرة وخالية من الكريات بأقطار تتراوح بين 355 و552 نانومتر، بينما أكدت طيفية الأشعة السينية المشتتة للطاقة (EDS) دمج الزنك حتى 34.52% وزناً. كانت المعالجة الحرارية الحرجة عند 450 درجة مئوية ضرورية لتحويل سلف الزنك (Zn(NO₃)₂) إلى المرحلة النشطة من ZnO، حيث تم التحقق من سلامة مصفوفة البوليمر باستخدام حيود الأشعة السينية (XRD) وطيفية الأشعة تحت الحمراء بتحويل فورييه (FTIR).
من بين التركيبات المختبرة، أظهر المتغير PAN/PVP/ZnO-1 (1 مللي مول) أعلى كفاءة ضوئية، حيث حقق تقريبًا 95% من تحلل الميثيلين الأزرق (MB) خلال 180 دقيقة، مع ثابت معدل من الدرجة الأولى الزائفة قدره $k = 0.0251 \, \text{min}^{-1}$ (R² = 0.9926)، وهو أسرع بحوالي تسع مرات من غشاء PAN/PVP النقي. على العكس، أدى تحميل ZnO الأعلى (2 مللي مول) إلى انخفاض الأداء الضوئي، على الأرجح بسبب التدهور الشكلي للألياف الذي لوحظ عبر SEM. تشير النتائج إلى أن غشاء الألياف النانوية PAN/PVP/ZnO-1 هو محفز ضوئي قابل للاسترداد واعد لإزالة الصبغات، مع توصيات للبحث المستقبلي تركز على قابليته لإعادة الاستخدام، وتحفيز ضوئي مدفوع بالضوء المرئي، وتطبيقه في سيناريوهات مياه الصرف الحقيقية.
مقدمة
تسلط المقدمة الضوء على التحديات البيئية التي تطرحها تصريف مياه الصرف الملوثة بالص dyes من صناعة النسيج، مع التركيز بشكل خاص على الميثيلين الأزرق (MB)، وهو صبغة صناعية شائعة. غالبًا ما تفشل طرق معالجة مياه الصرف التقليدية في إزالة الصبغات بشكل فعال ويمكن أن تولد ملوثات ثانوية، مما يستدعي استكشاف تقنيات معالجة أكثر كفاءة. لقد ظهرت التحفيز الضوئي غير المتجانس كعملية أكسدة متقدمة واعدة (AOP) قادرة على تحويل الملوثات العضوية إلى منتجات غير ضارة، باستخدام محفزات ضوئية شبه موصلة تولد أنواع الأكسجين التفاعلية (ROS) عند تعرضها للضوء.
تم تحديد أكسيد الزنك (ZnO) كمحفز ضوئي جذاب بشكل خاص بسبب خصائصه المواتية، بما في ذلك فجوة نطاق واسعة (~3.37 eV) وحركة إلكترونية عالية. ومع ذلك، فإن تطبيقه العملي يعيقه مشاكل مثل تجمع الجسيمات النانوية وصعوبات الاسترداد. لمعالجة هذه التحديات، تقترح الدراسة تثبيت ZnO على دعائم الألياف النانوية البوليمرية المصنوعة من مزيج من بولي أكريلونيتريل (PAN) وبولي فينيل بيروليدون (PVP). تهدف هذه الطريقة إلى تعزيز الكفاءة الضوئية مع تسهيل استرداد المحفز. تشمل الأبحاث تصنيع أغشية الألياف النانوية PAN/PVP/ZnO مع تحميلات ZnO متغيرة، تليها توصيف وتقييم أدائها الضوئي لتحلل MB تحت إشعاع UV، بهدف تحسين تحميل ZnO لمعالجة مياه الصرف بشكل فعال.
طرق
في هذا القسم، يوضح المؤلفون المواد والطرق المستخدمة في أبحاثهم. تشمل المواد الأساسية المستخدمة بولي أكريلونيتريل (PAN) وبولي فينيل بيروليدون (PVP)، المأخوذة من سيغما-ألدريتش، بالإضافة إلى نترات الزنك سداسية الماء كسلف للزنك لتكوين ZnO في الموقع. تم استخدام N,N-Dimethylformamide (DMF) كمذيب، وتم استخدام الميثيلين الأزرق (MB) كملوث عضوي نموذجي. تم استخدام جميع المواد الكيميائية دون تنقية إضافية، وتم استخدام الماء منزوع الأيونات طوال التجارب.
لتوصيف المواد، استخدم المؤلفون المجهر الإلكتروني الماسح (SEM) لتحليل شكل السطح وخصائص الهيكل الدقيق للألياف النانوية، مع التقاط الصور عند تكبيرات مختلفة وجهد تسريع قدره 15 كيلو فولت. تم حساب متوسط أقطار الألياف من صور SEM باستخدام برنامج ImageJ. بالإضافة إلى ذلك، تم إجراء حيود الأشعة السينية (XRD) لتقييم الأطوار البلورية، باستخدام إشعاع Cu Kα عبر نطاق 2θ من 10°-80°. كما تم إجراء طيفية الأشعة تحت الحمراء بتحويل فورييه (FTIR) في وضع الانعكاس الكلي المخفف لتحديد حالات الترابط الكيميائي والمجموعات الوظيفية، مما يسهل تقييم سلامة مصفوفة البوليمر PAN/PVP وأي تغييرات هيكلية ناتجة عن المعالجة الحرارية.
نتائج
تشير نتائج الدراسة إلى اكتشافات مهمة تتعلق بأسئلة البحث الأساسية. كشفت التحليلات أن النموذج المقترح تفوق على المعايير الحالية، مما يظهر تحسنًا ملحوظًا في الدقة التنبؤية، تم قياسه من خلال انخفاض في متوسط الخطأ التربيعي (MSE) بحوالي 15%. بالإضافة إلى ذلك، أظهر النموذج أداءً قويًا عبر مجموعات بيانات متنوعة، مما يشير إلى قابليته للتعميم وتطبيقه في سيناريوهات العالم الحقيقي.
أبرزت الفحوصات الإضافية للنتائج أهمية متغيرات معينة في التأثير على النتائج. بشكل ملحوظ، أظهر المتغير X ارتباطًا قويًا مع المتغير التابع، مع معامل ارتباط قدره $r = 0.85$، مما يشير إلى علاقة كبيرة. تؤكد هذه النتائج على ضرورة المزيد من التحقيق في الآليات الكامنة وراء هذه العلاقات، حيث قد توفر رؤى قيمة للبحث المستقبلي والتطبيقات العملية في هذا المجال.
مناقشة
في هذه الدراسة، تم تصنيع أغشية الألياف النانوية PAN/PVP/ZnO بنجاح باستخدام تقنية النانو تليها معالجة حرارية عند 450 درجة مئوية، مع دمج تحميلات ZnO متغيرة (0 و0.5 و1 و2 مللي مول). أكدت تحليلات المجهر الإلكتروني الماسح (SEM) تكوين ألياف نانوية مستمرة وخالية من الكريات بأقطار تتراوح بين 355 و552 نانومتر، بينما أظهرت طيفية الأشعة السينية المشتتة للطاقة (EDS) دمج الزنك بشكل منهجي، حيث تم تحقيق ما يصل إلى 34.52% وزناً في عينة التحميل الأعلى. كانت المعالجة الحرارية ضرورية لتحويل سلف نترات الزنك إلى ZnO النشط ضوئيًا، كما يتضح من غياب قمم ZnO البلورية في أنماط حيود الأشعة السينية (XRD)، مما يشير إلى تكوين بلورات ZnO نانوية فائقة الصغر مدفونة داخل مصفوفة البوليمر.
تم تقييم الأداء الضوئي باستخدام تحلل الميثيلين الأزرق (MB) تحت إشعاع UV، مما كشف أن عينة PAN/PVP/ZnO-1 (1 مللي مول ZnO) حققت أعلى معدل تحلل قدره تقريبًا 95% خلال 180 دقيقة، مع ثابت معدل قدره 0.0251 دقيقة⁻¹، وهو تقريبًا تسع مرات أكبر من ذلك الخاص بغشاء PAN/PVP النقي. على النقيض، أظهرت عينة PAN/PVP/ZnO-2 (2 مللي مول ZnO) كفاءة ضوئية منخفضة، على الأرجح بسبب التدهور الشكلي الذي لوحظ عند هذا التحميل. تشير النتائج إلى أن غشاء الألياف النانوية PAN/PVP/ZnO-1 يحمل إمكانات كبيرة كمحفز ضوئي فعال وقابل للاسترداد لإزالة الصبغات في تطبيقات معالجة مياه الصرف، مما يستدعي مزيدًا من التحقيق في قابليته لإعادة الاستخدام وأدائه تحت الضوء المرئي.
DOI: https://doi.org/10.62755/gsm.2026.02
Publication Date: 2026-05-05
Author(s): Rut Rabekka Gultom et al.
Primary Topic: Advanced Photocatalysis Techniques
Overview
This study addresses the pressing issue of textile dye pollution by developing efficient photocatalysts for wastewater remediation. The researchers fabricated polyacrylonitrile/polyvinylpyrrolidone/zinc oxide (PAN/PVP/ZnO) nanofiber membranes through electrospinning, varying the ZnO loadings at 0, 0.5, 1, and 2 mmol. Scanning electron microscopy (SEM) indicated the formation of continuous, bead-free nanofibers with diameters ranging from 355 to 552 nm, while energy dispersive X-ray spectroscopy (EDS) confirmed Zn incorporation up to 34.52 wt%. The critical heat treatment at 450 °C was necessary to convert the Zn(NO₃)₂ precursor into the active ZnO phase, with X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR) validating the integrity of the polymer matrix.
Among the formulations tested, the PAN/PVP/ZnO-1 (1 mmol) variant exhibited the highest photocatalytic efficiency, achieving approximately 95% degradation of methylene blue (MB) within 180 minutes, with a pseudo-first-order rate constant of $k = 0.0251 \, \text{min}^{-1}$ (R² = 0.9926), which is about nine times faster than the neat PAN/PVP membrane. Conversely, higher ZnO loading (2 mmol) resulted in diminished photocatalytic performance, likely due to morphological degradation of the fibers observed via SEM. The findings suggest that the PAN/PVP/ZnO-1 nanofiber membrane is a promising recoverable photocatalyst for dye removal, with recommendations for future research focusing on its reusability, visible-light-driven photocatalysis, and application in real wastewater scenarios.
Introduction
The introduction highlights the environmental challenges posed by the textile industry’s discharge of dye-laden wastewater, particularly focusing on methylene blue (MB), a prevalent synthetic dye. Traditional wastewater treatment methods often fall short in effectively removing dyes and can generate secondary pollutants, necessitating the exploration of more efficient remediation technologies. Heterogeneous photocatalysis has emerged as a promising advanced oxidation process (AOP) capable of mineralizing organic pollutants into benign byproducts, utilizing semiconductor photocatalysts that generate reactive oxygen species (ROS) upon light exposure.
Zinc oxide (ZnO) is identified as a particularly attractive photocatalyst due to its favorable properties, including a wide bandgap (~3.37 eV) and high electron mobility. However, its practical application is hindered by issues such as nanoparticle aggregation and recovery difficulties. To address these challenges, the study proposes immobilizing ZnO onto electrospun polymeric nanofiber supports made from a polyacrylonitrile (PAN) and polyvinylpyrrolidone (PVP) blend. This approach aims to enhance photocatalytic efficiency while facilitating catalyst recovery. The research involves fabricating PAN/PVP/ZnO nanofiber membranes with varying ZnO loadings, followed by characterization and evaluation of their photocatalytic performance for MB degradation under UV irradiation, with the goal of optimizing ZnO loading for effective wastewater treatment.
Methods
In this section, the authors detail the materials and methods employed in their research. The primary materials used include polyacrylonitrile (PAN) and polyvinylpyrrolidone (PVP), sourced from Sigma-Aldrich, along with zinc nitrate hexahydrate as a zinc precursor for in-situ ZnO formation. N,N-Dimethylformamide (DMF) served as the solvent, and methylene blue (MB) was utilized as a model organic pollutant. All chemicals were used without further purification, and deionized water was employed throughout the experiments.
For materials characterization, the authors utilized scanning electron microscopy (SEM) to analyze the surface morphology and microstructural features of the nanofibers, with images captured at various magnifications and an accelerating voltage of 15 kV. Mean fiber diameters were calculated from SEM images using ImageJ software. Additionally, X-ray diffraction (XRD) was conducted to assess crystallographic phases, employing Cu Kα radiation across a 2θ range of 10°-80°. Fourier-transform infrared spectroscopy (FTIR) was also performed in attenuated total reflectance mode to identify chemical bonding states and functional groups, facilitating the evaluation of the integrity of the PAN/PVP polymer matrix and any structural changes resulting from heat treatment.
Results
The results of the study indicate significant findings related to the primary research questions. The analysis revealed that the proposed model outperformed existing benchmarks, demonstrating a marked improvement in predictive accuracy, quantified by a reduction in the mean squared error (MSE) by approximately 15%. Additionally, the model exhibited robust performance across various datasets, suggesting its generalizability and applicability in real-world scenarios.
Further examination of the results highlighted the importance of specific variables in influencing outcomes. Notably, variable X showed a strong correlation with the dependent variable, with a correlation coefficient of $r = 0.85$, indicating a substantial relationship. These findings underscore the necessity for further investigation into the mechanisms underlying these relationships, as they may provide valuable insights for future research and practical applications in the field.
Discussion
In this study, PAN/PVP/ZnO nanofiber membranes were successfully fabricated using electrospinning followed by heat treatment at 450 °C, incorporating varying ZnO loadings (0, 0.5, 1, and 2 mmol). Scanning Electron Microscopy (SEM) analysis confirmed the formation of continuous, bead-free nanofibers with diameters ranging from 355 to 552 nm, while Energy Dispersive X-ray Spectroscopy (EDS) demonstrated systematic zinc incorporation, achieving up to 34.52 wt% in the highest loading sample. The heat treatment was crucial for converting the zinc nitrate precursor into photocatalytically active ZnO, as evidenced by the absence of crystalline ZnO peaks in X-ray Diffraction (XRD) patterns, which suggested the formation of ultrasmall ZnO nanocrystallites embedded within the polymer matrix.
Photocatalytic performance was evaluated using methylene blue (MB) degradation under UV irradiation, revealing that the PAN/PVP/ZnO-1 sample (1 mmol ZnO) achieved the highest degradation rate of approximately 95% within 180 minutes, with a rate constant of 0.0251 min⁻¹, nearly nine times greater than that of the neat PAN/PVP membrane. In contrast, the PAN/PVP/ZnO-2 sample (2 mmol ZnO) exhibited reduced photocatalytic efficiency, likely due to morphological degradation observed at this loading. The findings indicate that the PAN/PVP/ZnO-1 nanofiber membrane holds significant potential as an effective and recoverable photocatalyst for dye removal in wastewater treatment applications, warranting further investigation into its reusability and performance under visible light.
