DOI: https://doi.org/10.1002/admt.202502083
تاريخ النشر: 2026-03-20
المؤلف: Bhavani Prasad Yalagala وآخرون
الموضوع الرئيسي: علوم الأعصاب والهندسة العصبية
نظرة عامة
تقدم هذه الورقة استراتيجية تصنيع جديدة تهدف إلى تعزيز تطوير الأجهزة الطبية القابلة للارتداء والغرس، مع التركيز بشكل خاص على الأجهزة الإلكترونية القابلة للتحلل البيولوجي مثل مصفوفات الأقطاب الدقيقة (MEAs) وأجهزة استشعار الضغط القابلة للزرع. يبرز المؤلفون قيود تقنيات غرف النظافة التقليدية في العمل مع المواد القابلة للتحلل البيولوجي ويقترحون طريقة تصنيع بدون قناع وبدون تلامس باستخدام نظام ليزر متقدم يعتمد على الأشعة فوق البنفسجية. هذه الطريقة المبتكرة تنتج بنجاح مصفوفات أقطاب مرنة ومتوافقة مع الخلايا الحية وقابلة للتحلل البيولوجي، باستخدام ركيزة قابلة للتحلل البيولوجي مصنوعة من الكيتوزان وأقطاب زنك (Zn) قابلة للتحلل البيولوجي. من الجدير بالذكر أن مطيافية impedence الكهروكيميائية (EIS) تكشف عن مقاومة قدرها 10 كيلو أوم عند 1 كيلو هرتز، بينما تظهر ركيزة الكيتوزان قوة شد جيدة وتوافقًا حيويًا مع خلايا العضلات الذكية، مما يؤكد ملاءمتها للتطبيقات القابلة للزرع.
في الختام، تؤكد الأبحاث على أهمية طرق التصنيع المبتكرة في تقدم الأجهزة الطبية، مع التركيز على التعددية، والفعالية من حيث التكلفة، وقابلية التوسع، وقابلية التصنيع. تسهل تقنية التصنيع بالليزر المعتمدة على الأشعة فوق البنفسجية الإنتاج على نطاق واسع وإنتاج دفعات من مصفوفات الأقطاب المرنة والقابلة للتحلل البيولوجي، وأجهزة استشعار الضغط، والأقطاب العابرة. يتم تسليط الضوء على جهاز استشعار الضغط القابل للتحلل البيولوجي الكهروضغطي لقدرته الممتازة على الحساسية، والثبات الدوري، وقابلية التحلل البيولوجي، مما يظهر إمكانيات هذه الطريقة لتطبيقات الاستشعار القابلة للزرع والارتداء في المستقبل.
مقدمة
تسلط المقدمة الضوء على الحاجة المتزايدة للأجهزة الطبية الحيوية القابلة للزرع والتي تتسم بالتدخل الأدنى والعابرة، والتي يمكن أن تؤدي تشخيصات أساسية وتذوب بأمان في السوائل الحيوية، مما يلغي الحاجة إلى جراحات إضافية. تقدم هذه الأجهزة فوائد مثل تحسين راحة المريض، وتقليل مخاطر الجراحة، وانخفاض التكاليف. ومع ذلك، لا تزال هناك تحديات كبيرة، خاصة في تطوير مواد مرنة وقابلة للتحلل البيولوجي واستراتيجيات تصنيع فعالة تتوافق مع المواد البوليمرية الناشئة. يظهر الكيتوزان، وهو بوليمر حيوي مشتق من الكيتين، كمرشح واعد بسبب مرونته الميكانيكية، وشفافيته البصرية، وتوافقه الحيوي، وقابلية تحلله البيولوجي القابلة للبرمجة. على الرغم من مزاياه، تطرح تقنيات التصنيع الدقيقة التقليدية مشاكل توافق يمكن أن تؤثر على خصائص المادة.
لمعالجة هذه التحديات، تقترح الورقة نهج تصنيع جديد يعتمد على الليزر باستخدام ليزر بيكوثانية/فيمتوثانية لإزالة الطبقات المعدنية مباشرة، مما يسمح بإنشاء تصميمات أقطاب معقدة بدقة مع الحفاظ على سلامة ركيزة الكيتوزان. تقدم هذه الطريقة بديلاً غير تلامسي وبدون قناع لتقنيات غرف النظافة التقليدية. توضح الدراسة إعداد وتوصيف أفلام الكيتوزان الشفافة ذات المساحة الكبيرة وتصنيع مصفوفات الأقطاب الدقيقة القابلة للتحلل البيولوجي (MEAs) باستخدام أقطاب الزنك، بالإضافة إلى مصفوفات الأقطاب التقليدية المعتمدة على الذهب. تظهر تقييمات الأداء، بما في ذلك impedence الكهروكيميائي، واختبارات التوافق الميكانيكي، وتطوير جهاز استشعار ضغط مرن، التطبيقات المحتملة لهذه الأجهزة العابرة في مراقبة الضغط داخل الجمجمة واستخدامات أخرى قابلة للزرع، مع التأكيد على توافقها، وقدراتها على توليد الطاقة الذاتية، وعابريتها.
طرق
في هذا القسم، يوضح المؤلفون الطرق التجريبية المستخدمة في دراستهم. استخدموا كيتوزان منخفض الوزن الجزيئي وحمض الأسيتيك، وكلاهما مصدره من سيغما ألدريتش، المملكة المتحدة، جنبًا إلى جنب مع مياه مؤينة فائقة النقاء تم إنتاجها بواسطة نظام ميرك ميليبور لجميع التجارب. تم استخدام محلول فوسفات ملحي (PBS) بتركيز 1 م عند pH 6.5 كإلكتروليت، مع بلاتين (Pt) كقطب مضاد وقطب مرجعي من فضة/كلوريد الفضة (Ag/AgCl) لقياسات impedence الكهروكيميائي. أجريت التجارب في درجة حرارة الغرفة العادية باستخدام هدف زنك قابل للتحلل البيولوجي ولوحة نحاسية سوداء.
بالإضافة إلى ذلك، تم عزل خلايا العضلات الملساء من الشريان الأورطي للفئران (MASMCs) من فئران C57BLK6/J وتم تخزينها في النيتروجين السائل بكثافة 1 × 10^6 خلايا/مل في 10% ثنائي ميثيل سلفوكسيد (DMSO). تم استخدام عينات دماغ الحملان، التي تم الحصول عليها من مورد مرخص وفقًا للوائح رعاية الحيوان في المملكة المتحدة، دون تعديلات. يضمن هذا الإطار المنهجي الالتزام بالمعايير الأخلاقية مع توفير أساس قوي للتحقيقات التجريبية.
مناقشة
في هذا القسم، تناقش الأبحاث تطبيق ليزر بيكوثانية عالي الدقة في التصنيع الدقيق للأجهزة الطبية القابلة للزرع، مع التركيز بشكل خاص على مصفوفات الأقطاب الدقيقة القابلة للتحلل البيولوجي (MEAs) وأجهزة استشعار الضغط القابلة للتحلل البيولوجي. يتم تسليط الضوء على قدرة الليزر على تحقيق حد أدنى لحجم الميزات يبلغ 40 ميكرومتر وحد أقصى يبلغ 1 سم على الركائز الأكثر سمكًا، مع تصنيع ناجح على نطاق واسع لـ 180 MEAs غير قابلة للتحلل البيولوجي تظهر موثوقية تزيد عن 95%. ومع ذلك، أظهر تصنيع MEAs القابلة للتحلل البيولوجي باستخدام الزنك/الكيتوزان تباينًا كبيرًا بين الأجهزة (أكثر من 25%)، يُعزى إلى أعماق إزالة غير متسقة وحساسية الرطوبة للكيتوزان. تم الإبلاغ عن معدلات الإنتاج لمصفوفات الأقطاب المعتمدة على الذهب والزنك كـ 3000 و2160 جهازًا في اليوم، على التوالي، مما يدل على كفاءة الطريقة.
يتناول القسم أيضًا الخصائص الميكانيكية والكهربائية للأجهزة المصنعة، بما في ذلك نتائج impedence الكهروكيميائي (EIS) التي تكشف عن اختلافات في المقاومة بناءً على هندسة الأقطاب. تؤكد الدراسة على أهمية التوافق في تصميم الأجهزة العصبية، حيث تظهر أفلام الكيتوزان مرونة جيدة وقدرة على التكيف مع الأسطح البيولوجية، وهو أمر حاسم لتقليل استجابات الجسم الغريب. بالإضافة إلى ذلك، يتم استكشاف إمكانية استخدام الكيتوزان كمادة كهروضغطية لأجهزة استشعار الضغط، مما يظهر حساسية واعدة واستجابة خطية عبر أنظمة ضغط مختلفة. بشكل عام، تؤكد النتائج على تعددية وفعالية تقنية التصنيع الدقيقة المعتمدة على الليزر لتطوير أجهزة طبية حيوية متقدمة قابلة للزرع.
DOI: https://doi.org/10.1002/admt.202502083
Publication Date: 2026-03-20
Author(s): Bhavani Prasad Yalagala et al.
Primary Topic: Neuroscience and Neural Engineering
Overview
This paper presents a novel fabrication strategy aimed at enhancing the development of wearable and implantable medical devices, particularly focusing on bioresorbable electronic devices such as microelectrode arrays (MEAs) and implantable pressure sensors. The authors highlight the limitations of traditional cleanroom techniques in working with bioresorbable materials and propose a mask-free, contact-less fabrication method utilizing an advanced UV-based laser system. This innovative approach successfully produces flexible, cytocompatible, and biodegradable MEAs and pressure sensors, employing a biodegradable substrate made from chitosan and biodegradable Zinc (Zn) electrodes. Notably, electrochemical impedance spectroscopy (EIS) reveals an impedance of 10 kΩ at 1 kHz, while the chitosan substrate demonstrates good tensile strength and cytocompatibility with smart muscle cells, confirming its suitability for implantable applications.
In conclusion, the research underscores the importance of innovative fabrication methods in the advancement of medical devices, emphasizing versatility, cost-effectiveness, scalability, and manufacturability. The proposed UV-based laser fabrication technique facilitates large-area and batch production of flexible, biodegradable MEAs, pressure sensors, and transient electrodes. A piezoelectric biodegradable pressure sensor is highlighted for its excellent sensitivity, cyclic stability, and biodegradability, showcasing the potential of this method for future implantable and wearable sensing applications.
Introduction
The introduction highlights the increasing need for minimally invasive and transient biomedical devices that can perform essential diagnostics and dissolve safely in biofluids, thus eliminating the necessity for additional surgeries. These devices present benefits such as enhanced patient comfort, reduced surgical risks, and lower costs. However, significant challenges remain, particularly in developing flexible, bioresorbable materials and efficient fabrication strategies compatible with emerging polymeric materials. Chitosan, a chitin-derived biopolymer, emerges as a promising candidate due to its mechanical flexibility, optical transparency, biocompatibility, and programmable biodegradability. Despite its advantages, traditional microfabrication techniques pose compatibility issues that can compromise the material’s properties.
To address these challenges, the paper proposes a novel laser-based fabrication approach utilizing Picosecond/femtosecond lasers for direct ablation of metal layers, which allows for the precise creation of complex electrode designs while preserving the integrity of the chitosan substrate. This method offers a non-contact, maskless alternative to conventional cleanroom techniques. The study details the preparation and characterization of large-area transparent chitosan films and the fabrication of bioresorbable microelectrode arrays (MEAs) using zinc electrodes, as well as conventional gold-based MEAs. Performance evaluations, including electrochemical impedance, mechanical conformability tests, and the development of a flexible pressure sensor, demonstrate the potential applications of these transient devices in monitoring intracranial pressure and other implantable uses, emphasizing their conformability, self-powering capabilities, and transience.
Methods
In this section, the authors detail the experimental methods employed in their study. They utilized low molecular weight chitosan and acetic acid, both sourced from Sigma Aldrich, UK, alongside ultra-pure deionized water produced by a Merck Millipore system for all experiments. A 1 m Phosphate Buffer Saline (PBS) at pH 6.5 served as the electrolyte, with platinum (Pt) as the counter electrode and a silver/silver chloride (Ag/AgCl) reference electrode for electrochemical impedance measurements. The experiments were conducted at ambient room temperature using a biodegradable zinc target and a copper black plate.
Additionally, mouse aorta smooth muscle cells (MASMCs) were isolated from C57BLK6/J mice and stored in liquid nitrogen at a density of 1 × 10^6 cells/mL in 10% Dimethyl Sulfoxide (DMSO). Lamb brain samples, obtained from a licensed supplier in compliance with UK Animal Welfare and Animal By-product Regulations, were used without modifications. This methodological framework ensures adherence to ethical standards while providing a robust basis for the experimental investigations.
Discussion
In this section, the research discusses the application of a high-resolution UV picosecond laser for microfabrication of implantable medical devices, specifically focusing on bioresorbable microelectrode arrays (MEAs) and biodegradable pressure sensors. The laser’s ability to achieve a minimum feature size of 40 µm and a maximum of 1 cm on thicker substrates is highlighted, with a successful large-scale fabrication of 180 non-bioresorbable MEAs demonstrating over 95% reliability. However, the fabrication of bioresorbable MEAs using zinc/chitosan showed significant device-to-device variation (over 25%), attributed to inconsistent ablation depths and the moisture sensitivity of chitosan. The throughput rates for gold-based and zinc-based MEAs were reported as 3000 and 2160 devices per day, respectively, indicating the method’s efficiency.
The section further elaborates on the mechanical and electrical properties of the fabricated devices, including electrochemical impedance spectroscopy (EIS) results that reveal differences in impedance based on electrode geometry. The study emphasizes the importance of conformability in the design of neural devices, with chitosan films demonstrating good flexibility and adaptability to biological surfaces, which is crucial for minimizing foreign body responses. Additionally, the potential of chitosan as a piezoelectric material for pressure sensors is explored, showing promising sensitivity and linear response across various pressure regimes. Overall, the findings underscore the versatility and effectiveness of the laser-based microfabrication technique for developing advanced, implantable biomedical devices.
